Commercial, Strata & Residential Serving Vancouver, North Van, West Van, & Burnaby
Building Envelope RestorationExterior Coatings

Moss on a Building Is a Drainage Report You Can Read From the Street

Published: By: · SPRAT/IRATA certified · 40+ yrs Metro Vancouver Save
A Vancouver low-rise with heavy dark staining and streaking running down the stucco facade below window lines and roof edges.
Written by: Allweathercoating Technical Team
SPRAT- & IRATA-certified · 40+ years Metro Vancouver building envelope experience ·

Every building in Metro Vancouver grows something on its exterior. The climate guarantees it: a long wet season, mild temperatures, and enough shade on any given elevation to keep surfaces damp for weeks at a time.

Most owners see it as an appearance problem and schedule a wash. That is a reasonable response and it discards the more useful information, because the growth is not distributed randomly.

Growth follows water

Algae, moss, and lichen all need moisture and time. They colonize surfaces that stay wet longer than the surfaces around them, and they fail to establish where water leaves quickly.

That makes the pattern of growth on a building a record of how water actually moves across it. Not how the drawings said it would move, and not how it moved when the building was new, but how it moves now, after thirty years of settlement, coating, and modification.

Reading that record costs nothing and requires no equipment beyond a pair of eyes and a walk around the building.

What the patterns mean

A vertical streak below a window. Water is being concentrated at that point and shed down the wall face rather than being thrown clear. Usually a sill that does not project far enough, a drip edge that has degraded, or an end dam missing from a sill flashing.

A horizontal band under a roof edge or a projection. Water is running back onto the wall rather than leaving at the drip. On a building with gutters it can mean the gutter overflows at that point, which is the maintenance issue set out in the guide on gutters and downspouts on strata buildings.

Growth concentrated at one end of a balcony. That end holds water. The slope has flattened or reversed and you are looking at the low corner, which is the condition described in the post on balcony deck drain retrofits.

A patch around a penetration. Something is discharging or shedding water onto the wall below it: an overflow, a vent, a light fixture, an unsealed conduit.

A general spread across a whole north elevation. This one usually means what it looks like, which is shade and the regional climate rather than a defect. Even so, it deserves recording, because a north elevation that has always been mossy and is now noticeably worse has changed for a reason.

Distinguishing what is growing

Algae forms thin films, green or black, on damp surfaces. It is the least damaging and the easiest to remove, and the black staining commonly assumed to be dirt on stucco and concrete is frequently algae.

Moss builds a mat that holds a substantial volume of water against the surface. On a sloped roof it grows under the edges of shingles and tiles and can lift them. In a gutter or at a scupper it becomes a drainage obstruction. It is the type most worth removing promptly.

Lichen grows slowly and bonds tightly to the substrate. Removing it mechanically often takes some of the surface with it, which on a coated or soft substrate means the removal causes more damage than the organism did.

Cleaning method matters more than most people expect

Pressure washing is the wrong tool on most building exteriors, and it is the default tool because it is fast and visibly effective.

High pressure erodes soft substrates, opens up stucco and mortar, strips coatings, and forces water into the assembly through joints and openings that were handling ordinary rain perfectly well. On a rainscreen wall it can drive water past the cladding in volumes the cavity was never designed to drain.

Soft washing uses low pressure and an appropriate cleaning solution, allowing the chemistry to break down the growth rather than blasting it off. The comparison is set out in the post on pressure washing versus soft washing, and on almost every building exterior the soft wash is the correct choice.

Product selection has consequences beyond the wall. Runoff reaches landscaping, storm drains, and neighbouring property, so containment and product choice are part of the specification. On coated surfaces the product also has to be compatible with the coating, or the cleaning removes more than the growth.

Cleaning without correcting is a subscription

Where growth marks a genuine drainage or detailing fault, washing it off resets the appearance and changes nothing else. It returns on a schedule set by the underlying condition.

That is acceptable when the strata has decided the growth is cosmetic and the wash is planned maintenance. It is a waste when the pattern was pointing at a fixable fault that nobody looked at, and the same money spent once on the sill flashing would have ended the cycle.

The distinction requires somebody to look at the pattern before the cleaning crew removes the evidence. In practice that means the inspection happens before the wash, not after, and the findings get recorded.

Roofs and gutters are the priority

On sloped roofs, moss is a maintenance item rather than only a diagnostic one.

It establishes at the lower edges of shingles and tiles and grows underneath them, lifting the covering and creating a path for water. On a Metro Vancouver townhouse complex under tree cover, that process runs continuously through the wet season and it shortens the life of a roof measurably.

In gutters and at scuppers, growth is a drainage obstruction. A gutter with a moss mat in it holds water, overflows during heavy rain, and delivers that water onto the wall below, which is where the vertical staining patterns come from. Clearing it is the same task described in the post on roof drain and scupper maintenance, and on a low-rise it is the single highest-value item on the seasonal list.

Growth around a flat roof drain does the same thing at a smaller scale and with larger consequences, because a blocked drain on a flat roof produces ponding rather than an overflow.

Timing and access

Cleaning is best done when the growth is active and the treatment can work, and when the weather allows the surface to dry afterward.

In this region that means avoiding the deepest part of the wet season, when a treated surface never dries and runoff volumes are highest, and avoiding the hottest part of summer when products can dry on the surface before they act. Late spring and early autumn are generally the practical windows.

Access dictates cost more than the cleaning does. On a low-rise, ladders and lifts serve. On a tower, cleaning is a rope access operation and it becomes economic to combine it with inspection, sealant checks, and any minor repairs, so that one setup covers several tasks. That bundling is the same logic as the post on mechanical penetration sealing: the setup dominates the cost of small work at height.

Building a record

Photograph the growth patterns before each cleaning cycle, with enough context to locate them on the building. Map them against elevations.

Two cycles of that gives a comparison, and comparison is where the value is. Growth appearing in a location that was previously clean means water is now doing something it was not doing before, and it is worth investigating while it is still a stain rather than a leak.

This belongs in the seasonal routine described in the post on fall building maintenance for strata, alongside the drain clearing that reduces the moisture conditions in the first place.

A building tells you where its water is going. It just does it in green, slowly, over years, and most people wash the message off without reading it.


Sources and further reading

  • BC Housing, Building Enclosure Design Guide, moisture management and surface drainage, referenced 2026
  • Canada Mortgage and Housing Corporation, Best Practice Guide: Wood-Frame Envelopes in the Coastal Climate of British Columbia, referenced 2026
  • Metro Vancouver, liquid waste and stormwater discharge guidance for exterior cleaning operations, referenced 2026
  • Allweathercoating exterior cleaning and inspection records, Metro Vancouver, 2026

Frequently Asked Questions

Is moss on a building actually damaging?

It holds moisture against the surface, which extends the time that surface stays wet, and on porous materials it can work into the substrate. The larger issue is what its presence indicates, because moss grows where water lingers, and lingering water is the problem behind most envelope deterioration.

Why does growth appear in patterns rather than everywhere?

Because it follows moisture and shade. A vertical streak below a window, a band under a roof edge, or a patch at one end of a wall all mark places where water is running or collecting differently from the surrounding area, which is exactly what an inspector wants to know.

What is the difference between algae, moss, and lichen?

Algae forms thin green or black films on damp surfaces. Moss is a plant that builds a mat and holds substantial water. Lichen is a slow-growing organism that bonds tightly to the substrate and is the hardest to remove without damaging what it is growing on.

Does pressure washing solve it?

It removes the visible growth and does nothing about the moisture condition that produced it, so it returns. High pressure also damages many substrates, drives water into the assembly, and can strip coatings, which is why soft washing is preferred on most building exteriors.

What is soft washing?

It is cleaning with low pressure and an appropriate cleaning solution, allowing the chemistry rather than the force to do the work. It removes biological growth without the substrate damage and water driving associated with high-pressure equipment.

Will the growth come back after cleaning?

Yes, unless the moisture condition changes. Cleaning is a cosmetic reset with a predictable interval. Where the growth marks a genuine drainage or detailing fault, correcting that fault is what changes the outcome.

Does moss damage roofs?

On sloped roofs it holds water against the covering and can lift shingles or tiles as it grows under their edges. On flat roofs, growth around drains and in ponding areas is more of a drainage obstruction than a direct attack on the membrane, and both are worth removing.

Are chemical treatments safe for the building?

It depends on the product and the substrate, and on what is below. Runoff reaches landscaping, storm drains, and adjacent property, so product selection and containment are part of the job rather than an afterthought. Coated surfaces in particular need a product compatible with the coating.

Which elevations grow the most?

North elevations and any surface shaded by trees, adjacent buildings, or the building's own projections. In Metro Vancouver those surfaces stay damp for long periods through the wet season, which is the condition growth requires.

Should growth be recorded in an inspection report?

Yes, with locations and patterns rather than a general note. Where growth appears is diagnostic information, and a report that maps it gives the next inspection something to compare against, which turns a snapshot into a trend.

← Back to Exterior Coatings Guide All Resources
Request Quote